Carton Printing Stencils

PAINT CARTONS USING STENCILS WITH YOUR COPY, ARTWORK, OR DESIGNS IN MINUTES, FOR PENNIES!

Here is a great New Way to Save Time and Money by Printing your own Shipping Cartons or Boxes in just Minutes! Now you can simply buy cheap UNPRINTED stock cartons or shipping boxes and then Quickly and Easily Print them in your own shop or plant with Any Copy you can make on your computer. This can be Trademarks, Artwork, Text or even your Company Logo. It could also be product contents, instructions or any other information you wish. And it can be done in ANY COLOR in Minutes using the New Universal Stencils that can be used Hundreds of times and even stored for Re-use later.

Watch a Quick Video Demonstration About Carton Printing Below

What Is This New Stencil System?

This is a Revolutionary New Stencil-Making System that will allow you to create whatever logo, text or trademark you like on all of your cardboard boxes or shipping cartons in any Color in just Minutes. This is the Easiest to Use, Lowest Cost stenciling system on the market today and with it you can easily make your standard blank cartons look like they were printed Professionally and at a LOW COST that you can NOT BEAT. And Best of All, this can be done by almost anyone in your plant. This is New and is not available anywhere on the Internet at prices that are even close to these Special Limited Time Low Prices.

How Does It Work?

This system is so easy to use that you will have virtually No Training Costs. You simply Create your Text Copy or Design on any computer, using software that you already have and use your regular printer to print the design out on a transparency film (which is included in the kit.) Then use a Stencil Maker (Shown below) to transfer the transparency onto the stencil material in 2 to 3 minutes. Develop the stencil, and you've got a Re-usable Stencil that will professionally print your cartons for less than a penny per box! (NOTE: See below for complete details)

What Will It Do For You?

Save You Time, Save Money, Give You Free Advertising and Make Your Boxes and Shipping Cartons Look Professional. How about doing all of that in a few Minutes and for less than a penny per box? And because the stencil can be reused hundreds of times, you can print just a few cartons for a small shipment, or do a big production run with just the one stencil. You can stencil whatever color you want, even in multiple colors! Add "Fragile" logos, or Haz-Mat warnings, or even contents to each box, making Shipping and Receiving Easier. You could even stencil your barcode on the side of each box. The Possibilities are Endless.

Best of all, this same stencil can be used for Thousands of Other Uses in your plant, shop or office because it can be used to Etch Metal Parts or Tools, Etch Glass, Ceramic or with Ink or Paint it can be used on Wood, Plastic, Leather, Paper, Tile, Fabric (Like T-Shirts) or almost anything else that will take Paint or Ink. Just glance through this website and you will find Hundreds of other Uses for this New Stencil Making System That You can use in your Plant or Office. You may want to Permanently Etch your company name on your tools or put a Trademark on some of your products....and You Can Do It Easily With This System in Minutes. So here you have a Multi-Purpose Stencil System you can use everywhere in your plant that will save you Time and Money and solve many problems of Putting Information on Just About Anything. So to see just how easy this is simply have a look below.

1. Print Your Copy or Artwork on a Transparency
	You can put any kind of copy or artwork on your Cardboard Boxes (Including Trademarks) in minutes. Simply put the copy on your computer and print out on the transparency sheets provided in your kit like shown at left.
2. Expose Your Stencil
	Now cut a piece of unexposed stencil material from the silver envelope to the appropriate size and place on the black pad in your exposure unit. Take your transparency sheet with the copy and place on top. Then cover with the glass plate and expose for two minutes.
3. Peel the Mylar Backing off Both Sides of the Stencil
	After exposure remove the stencil from the exposure unit and then peel the Mylar cover sheets from BOTH SIDES of the stencil.
4. Develop Your Stencil in Minutes.
	Next place the stencil in the developer solution and let it sit for about a minute. Then take one of the white sponges and gently rub the stencil where the copy shows. Rub on both sides of the copy until it becomes very WHITE. It is then ready for use.
5. Rinse the Developer off Completely.
	Rinse the stencil under warm water until the developer is completely cleaned off. You can tell this when the stencil is not slippery any longer.
6. Blot Dry Your Stencil with Paper Towel or Cloth.
	Wipe the stencil off to remove the excess water and then hold stencil up to the light to be sure that it is completely developed. There should be no Blue in the White letters or copy. If so then simply put back in the developer until the whole stencil copy is white.
7. Blow Dry Your Stencil
	Put stencil on a paper towel and "Blow Dry" it with a hair dryer for a few moments on both sides. It is easier to handle this way and this is also the best way to "Store" stencils after use.
8. Attach a Frame to Your Stencil (Optional)
	You may want to attach a frame to your stencil to make it easier to handle. (This is NOT absolutely necessary since a lot of times it is just as easy to use the stencil without a frame) We have Oak Frames available that work much better than the plastic ones shown. (See Below). Attach the stencil to the frame with cellophane tape on the edges.
9. Framed Stencil - Ready to Use.
	If you use a frame it should look like this. You can either use a Plastic or Wood frame. It works best to attach the stencil to the Underside of the frame so the stencil lies directly on the substrate (box) or anything to be marked. For info on frames see below. We have found that the Oak frames shown below are better and cheaper than the plastic ones.
10. Apply Ink To Your Stencil (Or To Squeegee)
	Put the proper ink on your stencil (Or on the Squeegee). Be sure you use enough ink or paint so that all the letters or copy on the stencil "Fills" and you do not get voids.
11. Use Squeegee
	Use a squeegee to evenly apply the ink or paint. Be sure that the width of the squeegee is wide enough to cover all of your copy so you DO NOT have to make a SECOND stroke. A second stroke can sometimes make a print that is over inked in the middle.
12. Hold Stencil Firmly and Position Squeegee
	Now pull squeegee across the carton in one smooth pass using about a 45 degree angle and moderate hand pressure. It is best to practice once or twice on scrap cardboard to get the "feel" of operating the squeegee and be sure the stencil is working perfectly. After a couple of tries you will be an Expert.
13. Pull Squeegee Across the Stencil.
	If you want to print on two sides of the carton simply move the stencil over and draw the squeegee across it again. It should easily have enough ink on it for several marks.
14. Gently Lift Your Stencil to Avoid Smearing.
	Note: Be sure when lifting the stencil that you are careful since the ink is wet and can smear easily. Therefore hold one edge and gently lift the opposite edge up and away from the wet ink. You will have a perfect mark then every time.
15. Cartons Can Be Printed on All Sides.
	Here is a carton that is printed on only one end simply as a sample. Printing on all four sides will require you to wait for several minutes or so until the first side dries. This usually is not a problem if you are doing a lot of cartons since some will be drying while you print others.
16. Single Carton
	Your printed cartons will look like this (Or Better) and can have more than one color and can be printed with graphics and on all edges including the flaps if you wish. Simply make the stencils larger to cover the larger area needed.
17. Multiple Cartons
	One stencil will print hundreds of boxes and can be cleaned, dried and stored to use over and over again. You can also use the same stencil and change the paint or ink color.
18. Wash Stencil for Reuse
	When finished simply clean up with water. If the stencil is a little "Plugged Up" because some of the ink has dried in it you may want to use a little white sponge and gently rub the area. It is best to NOT LET THE INK DRY in the stencil and you can prevent this by quickly going from one box to the other without waiting long periods between boxes allowing the paint to harden. Blow Dry stencils after use for best storage.

There You have it...Simple, Easy, Quick, Inexpensive and Anyone in your plant can become an Expert in Minutes. But Best of All, this Stencil System can be used on Glass, Metal, Plastic, Paper, Cardboard, Ceramic, Porcelain, Wood and any other Material that will accept Paint or Ink. So this opens up Hundreds of Possibilities that you can use in your business for Fun and Profit. You are only limited by your own Imagination and Energy. Also you may want to consider using your new stencils to ETCH YOUR METAL TOOLS with your company name. This is an excellent way to cut down on tools getting "Borrowed" and not returning. This is just ONE way your new Stencil Maker will Save You Money. For details on Tool Marking... Click Here For Tool Marking Info.

There are many other ways you can use Your New Stencil Maker in Your business so please take a few moments and examine this site and consider all of the ideas that you can easily use and Be Sure And Take Advantage of the Special Low Prices on these New Kits during this Limited Time Offer. Simply decide on the actual Size of the Stencil you may want to use....such as 5"x 6" or 6"x 8" or 10"x 12" and let that help you decide on the kit you will find the most Economical.

Here Are The Best Kits And Supplies On Sale Today!

MARK 440 STENCIL MAKER KIT
(Makes Stencils Up to 4"x 6")
Contents:

1 UV Exposure Unit in Aluminum Frame Measuring 5"x6"x12" High with Electric Cord, Switch and Special 365 Nanometer Ultra-Violet Bulb (120 Watts)
1 Aluminum Exposure Tray with Compression Foam and Glass Top.
1-16oz. Bottle Stencil Developer
1 Plastic Developing Tray with Lid.
2 White Developer Sponges.
1 Digital Timer.
10 Unexposed Universal Stencils 5"x6".
2 FREE Samples of Universal Stencils FOR PRACTICE.
5 Sheets Transparency Film For Your Copy (8 1/2"x 11")
1 Sample Glass Etching Kit with Etching Cream
Complete Instructions.

Mark 220 Stencil Maker Kit

$209.95!

MARK 680 STENCIL MAKER
(Makes Stencils Up To 6"x 8")
Contents:

1 UV Exposure Unit measuring 6"x8"12" High with a 1000 Hour Special UV Bulb, cord & switch.
1 Exposure Tray with Glass Top
1-16oz. Stencil Developer
1 Developing & Curling Tray
2 White Sponges
1 Digital Timer
10 Unexposed Universal Stencils 6"x8".
2 FREE Sample TEST Stencils (for practice)
Complete Instructions
1 Sample Glass Etching Kit with Etching Cream

Mark 680 Stencil Maker Kit

$308.95!

This Is the Best Size To Use for Carton Marking!

MARK 1000 STENCIL MAKER KIT
(Makes Stencils Up To 10"x 12")
Contents:

1 UV Exposure Unit Measuring 10"x12"x12" High with a 1000 Hour Special UV Bulb, Cord & Switch.
1 Exposure Tray with Glass Top.
2 White Sponges
1-16oz. Stencil Developer
1 Digital Timer
10 Unexposed Stencils 10"x12"
Complete Instructions
1 Sample Glass Etching Kit with Etching Cream

Mark 1000 Stencil Maker Kit - Best Size for Carton Making

$370.95!

Here Is A Great Way To Get Started!

We Can Make Custom Stencils For You With Your Artwork, Designs or Text Copy So You Can "Try Out" These New Universal Stencils. All You Do Is Make Up Your Copy on Your Computer And Email It To Us. (Note: It MUST BE Ready To Photograph And Make A Stencil From. We Can NOT Re-do Your Artwork) But You Can "Gang" Your Copy or Designs To Get Maximum Use Out Of Your Stencil. Then You Can Cut Out Individual Stencils To Use Any Way You Wish. If This Is Not Clear to You Simply Call, Fax or Email Us and We Will Explain How To Do This. Email Us Your Artwork For A Quote sales@stencil-maker.com

Size	Price Each	Duplicate
4"x5"	$24.95	$14.95
5" X 6"	$35.95	$25.95
6" X 8"	$49.95	$39.95
8 1/2 " X 11"	$69.95	$59.95

Martronics can help you make art stencils, craft stencils,
custom stencils, paint stencils and design stencils.

Martronics Corporation
PO BOX 200/500 Wilcox RD, Salkum, WA 98582
Ph:800-775-0797 Fax:360-985-2996
Email - Click Here